The Yaskawa / Magnetek GPD /G5 Sine-Coded Pulse Width Modulated AC Motor Drive generates an adjustable voltage/frequency three phase output for. TTThhhooommmpppsssooonnn CCCooo RRReeellleeeaaassseeeddd /// /// 2. Magnetek GPD AC Drive Start Up and Adjustment Guide. Magnetek G5 GPD | Drives | NEW IN STOCK | CALL or Click for Quote.
|Published (Last):||20 July 2011|
|PDF File Size:||11.21 Mb|
|ePub File Size:||6.98 Mb|
|Price:||Free* [*Free Regsitration Required]|
Magnetek GPD Yaskawa AC Drive Control Gpdc-a 3phase | eBay
In most configurations either the local reference d 1 – 0 1 or the remote AUTO reference will be utilized. Filters should have a solid connection from filter ground terminal to the cabinet ground point. Selectable Functions Multi-step speed operation gdp steps max. The Quick Guide to AC Variable Frequency This ebook is meant as an easy guide to any electrical or electronic engineer or technician, who would like to know how modern ac variable frequency drives work.
However, output frequency will be zero if the frequency reference is zero at the time this key is pressed. Each is set in increments of 0.
User Parameter Default Value Factory setting: If one or both channels do not have the correct pulses present i. When o 2 – 0 3 is not set to ” 1 “, this option is not available. At that point you can call on the repair experts at Precision Electronic Services, Inc. Thank you very much. If this occurs, the motor will coast to a stop.
Continued Continued Data A: Select 1 Jog Freq. When an external Jog signal is present, it will override the existing operation mode and the drive will ramp to the level set by this parameter. Mouse over to Zoom – Click to enlarge. In such cases, the integral reset function should be ON until the start of run operation. For main circuit input cables, a screened cable is recommended within the panel, and is also suggested for external connections.
A Critical Frequency Fpd Stopping Method Selection Factory setting: Sets the incoming Magnetel voltage to the drive.
Yaskawa Magnetek GPD Gpdc-b Spec 40p71f 2 HP Drive 3ph v | eBay
Be the first magneetek write a review. Connect the common of the scope to terminal 2 of 551. This is achieved by dissipating the regenerative energy of the AC motor across the resistive components of the Dynamic Braking option. After power recovery, if the drive output current is larger than the set value of b 3 – 0 2speed search is started, using a decel rate per the setting of b 3 – 0 3.
M Zero Servo fault Shaft position changed by more thanrevolutions during zero servo operation. Prohibited Frequency 2 d 3 – 0 3: Excessive droop, which results in a significant difference between the speed reference and the speed feedback, magnete activate a Speed Deviation D E V fault.
Pressing and holding this key will magnteek Jog function: Note 2 Drive capacity selection fault o has been changed from the correct factory setting value. Verify that the drive power voltage select connector, located at lower left corner inside drive chassis see Figure bis positioned correctly for the input power line voltage.
Fast and efficient service!
Because of their professional and quick service we avoided extensive downtime and were able to continue operations, thereby avoiding a potential production disaster. Disabled if the drive is programmed to use an external JOG input. If E 3 – 0 1 is set to a 2 or a 3, the second motor needs to be auto-tuned.
Maximum droop is reached at full load.
Pressing this key will decrease the value of the blinking digit in the display by 1. It is mandatory that the person who operates, inspects, or maintains this equipment thoroughly read and understand this manual before proceeding.
Defines the assignment of the signal at terminal 8. Does Not Rotate at Set Speed Setting Description 0 Output phase bpd detection disabled 1 Output phase loss detection enabled 5. Speed Search Deceleration Time Factory setting: Use manetek R and l2 S for single-phase input.
Torque Detection Selection 2 Factory setting each: All of these parameters are interactive, and will need to be adjusted until the control loop is properly tuned, i. No part of this document may be stored in a retrieval system, or transmitted, in More information. A straight length of wire moves through a uniform magnetic field.
Fuse Blown Protection Motor coasts to a stop by blown fuse. Remove power, remove the old control board, and install the new control board. It takes continuous life cycle management to make price leadership a sustainable More information.
Yaskawa / Magnetek GPD 515/G5 Sine-Coded Pulse Width Modulated AC Motor Drive
Prices are fair considering these things are as rare as unicorns. They provided me with a quality piece of equipment that allowed me to get my paint booth exhaust fan back up and running for a minimal cost, and the shipping was extremely quick as well.
Dwell Time at Start Factory setting: Zero-Servo Gain Factory setting: Skip to main content. Make sure you know which polarity you have on your VOM.
M Momentary power loss Low voltage has been detected, but momentary power loss ride-thru is enabled Land momentary power loss ride-thru time L has not yet been exceeded.